First, the repair of the sprinkler pump 1. The shell of the pump shell can be repaired by welding or bonded with epoxy resin. The bearing seat hole can be worn out too much. It can be repaired by the bushing method. If there is any pit, groove or unevenness in the end face of the pump shell, the lathe can be turned. repair. 2, pump shaft corrosion. You can use the tin to fill the spots, recesses, and then round. The pump shaft wear can be chrome plated and the bearing rotation should be flexible and noiseless. 3, water seal wear, rubber seal aging, deformation or damage, weakened water seal spring force or corrosion should be replaced. Second, sprinkler pump repair and test: 1. Assemble the sprinkler truck's water pump shaft and impeller, so that the end face of the impeller hole should be 0.10-0.50mm higher than the end of the pump shaft (refer to the pump with the impeller fixed by the bolt) for compaction. Refit the gasket, tighten the fixing bolt, install the water seal assembly, and lock it with a pin. 2. Put the pump impeller into the pump housing, put the rear bearing lock ring on one end of the shaft, and then install the rear bearing, spacer, and front bearing into the pump housing in turn (some pump bearings are integral type, then Install the integral bearing into the pump housing), review its fit, and insert the lock ring. 3. Mount the V-belt hub at the front end of the pump shaft, fasten it with bolts, and then attach the V-belt pulley and fan blade, tighten with a nut, but lock with an open lock (or locking piece). 4, install the pump cover and liner (some pumps do not have a cover). The clearance between the impeller and the cover (without the cover requires a clearance of 0.17-0.75 mm between the impeller and the front wall of the cylinder). 5. After the pump V pulley is installed, the oscillating error in the slot should not exceed 1.0 mm. The general rule of thumb is that when the impeller is moved, the pin feels like a gap. 6, the pump should be tested before loading. Experience is as follows: Turn the V-belt by hand, there should be no jamming phenomenon, block the inlet of the pump casing, and then add water to the impeller working chamber, turn the pump shaft, and the inspection hole should be leaked without water. If there is jamming and water leakage, the cause should be identified and eliminated. When conditions permit, the water pump should be installed on the test bench to run the test to check the displacement and whether there is water leakage (no test bench can be compared with the new pump). After the test is completed, the pump should be filled with grease. Xigong Chusheng (Hubei) Special Purpose Vehicle Co., Ltd. is a research, development, manufacturing, sales Chusheng brand tanker, Dongfeng tanker, Foton tanker, liberation tanker, sprinkler, sanitation garbage truck, Garden Sprinkler, Dongfeng Sprinkler, Fire Sprinkler, High Pressure Washer, Concrete Mixer, Cement Mixer, Refueller, Oil Truck, Sewage Suck, Garbage Truck, Suction Truck, Bulk Cement Truck, Powder Material Vehicle , lorry crane trucks, truck cranes, coach vehicles, led advertising vehicles, flatbed trucks, excavator transport vehicles, fire sprinklers and other special vehicles, a total of seven series of more than 200 varieties of wholly-owned private enterprises, It is a member of Dongfeng Company, FAW Group, CNHTC Group and Beiqi Futian Company. It covers an area of ​​150,000 square meters and a building area of ​​100,000 square meters. It has more than 560 employees and 180 engineering technicians. The main production equipment is More than 300 sets (sets), of which there are advanced flexible sealing device head and 8 × 9000 electronic control board machine, 9 m puzzle automatic welding machine, Germany Berg large displacement double-screw air compressor , PLC control of the wind cycle machine peening room, water spin paint spray room, drying room and machining, punching number of plasma cutting machines and other domestic leading equipment and tooling molds and testing equipment, total capital of more than 90 million. Strong technical force, advanced inspection methods, and perfect products have won wide acclaim from users for their high quality and low price, reliable performance, and timely service. Machining Plastic has a small density, light weight, can be insulated. machining Plastic is the use of CNC machining out, including drilling. Cutting, turning, machining Plastic commonly used products are: PA PC, Tetlon POM, PMMA. , we have a special inspection room to test the products, to ensure that and each size in line with the requirements of the drawings, but also a special machine for the production of material to withstand voltage insulation test. Applied in a variety of industries, including: drone, ship, communications, medical equipment, industrial automation equipment. Machining Plastic,Oem Precision Machining Plastic,Cnc Machining Plastic,CNC Plastic Machining Hong Kong RYH CO., LTD , https://www.szcncmachining.com
Sprinkler sprinkler
Maintenance and Repair of Sprinkler Pump for Chusheng Sprinkler
Xigong Chusheng sprinkler pumps use centrifugal type. In use, common damages include: cracked pump casing, wear and bending of the pump shaft, impeller cracking, bakelite washer and washer seat damage, aging of the rubber water seal, wear of the water seal seat, V-belt wheel hub and pump shaft, Keys and keyways are loose and loose. After damage occurs to the sprinkler water pump, it will cause poor water absorption, insufficient pressure, leaking gas and other faults, which will cause the diesel engine to overheat and affect the normal operation of the diesel engine. Therefore, it should be repaired and maintained: